- 您現在的位置：買賣IC網 > PDF目錄363904 > W90210F (WINBOND ELECTRONICS CORP) PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) PDF資料下載
參數資料
| 型號： | W90210F |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
| 中文描述： | 32-BIT, MROM, RISC MICROCONTROLLER, PQFP208 |
| 封裝： | PLASTIC, QFP-208 |
| 文件頁數： | 37/67頁 |
| 文件大小： | 297K |
| 代理商： | W90210F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
W90210F
37
Version 1.4, 10/8/97
The above information is the exclusive intellectual property of Winbond Electronics Corp. and shall not be disclosed, distributed or reproduced without permssion fromWinbond.
In Standard mode or Parallel FIFO mode, this bit is forced to 0. The drivers are enabled, i.e. the
data pins of the parallel port are always outputs. Otherwise, this bit tri-states the data output
drivers, so that data will be read from the peripheral.
Bit [3]- ackIntEn
1: Enable an interrupt on the rising edge of nAck.
0: Disable the nAck interrupt (default)
Bit [4]- SelectIn; is inverted and then driven as parallel prot nSelectIn (default 1).
Bit [5]- nInit; is driven as parallel port nInit (default 1).
Bit [6]- autofd; is inverted and then driven as parallel port nAutoFd (default 0).
In centronic peripheral mode, when the nAck is active, the bit will be cleared by hardware.
Bit [7]- strobe; is inverted and then driven as parallel port nStrobe (default 0).
4. ECR register (offset 243) (R/W)
0
7
Bit[0:2]- mode (R/W)
000: Standard parallel port mode (default).
In this mode, FIFO is reset and common collector drivers are used on the control lines (nStrobe,
nAutoFd, nInit, and nSelectIn). Direction bit is cleared to "0".
001: PS/2 parallel port mode
The direction could be forward or reverse. In reverse direction, reading the data register returns the
value on the data lines not the value in the data register.
010: Parallel port FIFO mode
This is the same as Standard parallel port mode except that Pwords are written or DMAed to the
FIFO. FIFO data is automatically transmitted using the standard parallel port protocol. Note that
this mode is only useful when the direction bit is 0.
011: ECP parallel port mode
In the forward direction, Pwords is placed into the FIFO and transmitted automatically to the
peripheral using ECP protocol. In the reverse direction, bytes are moved from the ECP data port
and packed into Pwords in the FIFO. All drivers have active pull-ups.
100: Centronic peripheral moe
In this mode, the parallel port acts as a reverse port in centronics mode and the direction bit is
forced to 1. The nAutofd bit (DCR bit 6) is cleared, nAck is active until nAutofd bit (DCR bit 6) is
set to 1 by software. And the parallel port data will be latched in the data register.
101: Reserved
110: Test mode
In this mode, the FIFO may be read or written, but the data will not be transmitted on the parallel
port. Using this mode to test the depth of the FIFO, the write-threshold, and the read-threshold.
111: Configuration mode
In this mode, the CNFGA and CNFGB registers are accessible at addresses 244 and 246
Bit[3]- nErrIntrEn (R/W, Valid only in ECP mode)
1: Disable the interrupt generated on the asserting edge of nFault (default).
0: Enables an interrupt pulse on the high to low edge of nFault.
Note that an interrupt pulse will be generated if nFault is asserted and this bit is written from a "1" to a
"0". This prevents interrupts from being lost in the time between the read of the ecr and the wrtie of the
ecr.
Bit[4]- dmaEn (R/W)
1: Enables DMA, DMA starts when serviceIntr (bit 5) is 0.
0: Disables DMA unconditionally (default).
Bit[5]- serviceIntr (R/W)
1: Disables DMA and all of the service interrupts (default).
0: Enables one of the following 3 cases of interrupts. Once one of the 3 service interrupts has
occurred, serviceIntr bit shall be set to a "1" by the hardware. Writing this bit to a "1" will not cause
an interrupt.
case 1: dmaEn = 1
During DMA (this bit is set to a 1 when terminal count is reached)
case 2: dmaEn = 0, direction = 0
This bit shall be set to 1 whenever there are writeIntrThreshold or more Pwords free in the
FIFO.
case 3: dmaEn = 0, direction = 1
相關PDF資料 |
PDF描述 |
|---|---|
| W90220F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
| W90221F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
| W91030B | Low Power CMOS IC For Caller indentification(用于通信中呼叫確認的低功耗CMOS集成電路芯片) |
| W91030 | Low Power CMOS IC For Caller indentification(用于通信中呼叫確認的低功耗CMOS集成電路芯片) |
| W91031 | LOW POWER CMOS INTERGRATED CIRCUIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W902E31 | 制造商:Omron Corporation 功能描述: |
| W903B-28C | 制造商: 功能描述: 制造商:undefined 功能描述: |
| W903B48D | 制造商: 功能描述: 制造商:undefined 功能描述: |
| W905 | 制造商:LUMINIS 制造商全稱:LUMINIS 功能描述:Post top mount |
| W9050B016 | 制造商:Pulse Electronics Corporation 功能描述:1.13OD 1.6'' I-Pex to I-Pex Cable Assembly |
發布緊急采購，3分鐘左右您將得到回復。