- 您現在的位置：買賣IC網 > PDF目錄363893 > W6692 (WINBOND ELECTRONICS CORP) PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) PDF資料下載
參數資料
| 型號： | W6692 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP100 |
| 封裝： | 14 X 20 MM, 2.75 MM HEIGHT, QFP-100 |
| 文件頁數： | 46/84頁 |
| 文件大小： | 473K |
| 代理商： | W6692 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
W6692
- 46 -
MFD Multiframe Disable
This bit is used to enable or disable the multiframe structure on S/T interface:
0 : Multiframe is enabled
1 : Multiframe is disabled
DLP Digital Loopback
Setting this bit activates the digital loopback function. The transmitted digital 2B+D channels are
looped to the received 2B+D channels. Note that after hardware reset, the internal clocks will turn off
if the S bus is not connected or if there is no signal on the S bus. In this case, the C/I command ECK
must be issued to enable loopback function.
RLP Remote Loopback
Setting this bit to "1" activates the remote loopback function. The received 2B channels from the S
interface are looped to the transmitted 2B channels of S interface. The D channel is not looped in
this loopback function.
8.1.5 D_ch Timer Register
D_TIMR
Read/Write
Address 10H
Value after reset: FFH
7
6
5
4
3
2
1
0
CNT2
CNT1
CNT0
VAL4
VAL3
VAL2
VAL1
VAL0
CNT together with VAL determine the time period T2 after which a TEXP interrupt will be generated:
T2 = CNT * 2.048 s + T1 with T1 = (VAL +1) * 0.064 s
The timer is started by setting the STT bit in D_CMDR and will be stopped when a TEXP interrupt is
generated or the D_TIMR register is written.
Note: If CNT is set to 7, a TEXP interrupt is generated periodically at every expiration of T1.
This register can be read only after the timer has been started. The read value indicates the timer's
current count value. In case layer 1 is not activated, a C/I command "ECK" must be issued in addition
to the STT command to start the timer.
8.1.6 Interrupt Status RegisterISTA
Read_clear
Address 14H
Value after reset: 00H
7
6
5
4
3
2
1
0
D_RMR
D_RME
D_XFR
D_EXI
B1_EXI
B2_EXI
D_RMR D_ch Receive Message Ready
A 64-byte data is available in the D_RFIFO. The frame is not complete yet.
相關PDF資料 |
PDF描述 |
|---|---|
| W6693A | USB Bus ISDN S/T Interface Controller(USB總線的ISDN S/T接口控制器) |
| W6694 | PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) |
| W6810 | SINGLE-CHANNEL VOICEBAND CODEC |
| W6810IE | SINGLE-CHANNEL VOICEBAND CODEC |
| W6810IR | SINGLE-CHANNEL VOICEBAND CODEC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W6692A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
| W6692ACD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
| W6692ACF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
| W6694 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:USB Bus ISDN S/T-Controller |
| W6694A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with USB 1.1 Interface |
發布緊急采購，3分鐘左右您將得到回復。