- 您現在的位置：買賣IC網 > PDF目錄363903 > W83877AF (WINBOND ELECTRONICS CORP) Multi-Function I/O Port Controller(多功能輸入／輸出口控制器) PDF資料下載
參數資料
| 型號： | W83877AF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | Multi-Function I/O Port Controller(多功能輸入／輸出口控制器) |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP100 |
| 封裝： | QFP-100 |
| 文件頁數： | 104/171頁 |
| 文件大?。?/td> | 1634K |
| 代理商： | W83877AF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁當前第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁
W83877AF
Publication Release Date: Dec. 1996
Preliminary Version 0.52
- 102 -
(4) If the parallel port is set to EXT2FDD mode after the system has booted DOS or another operating
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
5.6 Extension Adapter Mode (EXTADP)
(Patent pending)
In this mode, the W83877AF redefines the printer interface pins for use as an extension adapter,
allowing a pocket peripheral adapter card to be installed through the DB-25 printer connector. The pin
assignments for the extension adapter are shown in table 5-1.
XDO-XD7 are the system data bus for the extension adapter.
XA0-XA2 are the system address bus.
XWR
and
XRD
are the I/O read/write commands with address comparing match or in DMA
access mode.
XDACK
,
XTC
,
and XDRQ are used in conjunction with
PDACKX, TC, and PDRQX to execute
a DMA cycle.
The extension adapter can issue a DMA request by setting pin XDRQ high, thus sending the
W83877AF output to the host system by pin PDRQX. The DMA controller should recognize the DMA
request and output a relative DACK to pin PDACKX
of the
W83877AF, which will output the DACK
without any change from pin
XDACK
to the extension adapter. Once the DMA transfer is completed,
a terminal count (TC) should be issued from the DMA controller to pin TC of W83877AF and output to
the extension adapter via pin XTC. XIRQ is the interrupt request of the extension adapter. The value
of XIRQ coming from the extension adapter will directly pass through pin IRQ7 to the host system.
XIRQ and IRQ7,
XDACK
and
PDACKX
,
and
XDRQ and PDRQX are three input/output pairs of
W83877AF pins. Although these pins are defined as DMA and interrupt functions, they can be
redefined by users for other specific functions.
5.6.1 Operation
The idea behind EXTADP mode is to treat the parallel port DB-25 connector as an ISA slot, except
that its addresses are not issued to the extension adapter. The operation of EXTADP mode is
described below:
1. Set the W83877AF to EXTADP mode by programming bit 7 of CR7 as low and bit 3 and bit 2 of
CR0 as high and low, respectively.
2. The W83877AF CR2 is an address register that records the address of the extension adapter.
When the desired address is written into CR2, pins
XWR
and
XRD
of the W83877AF will
simultaneously go low and the desired address will also appear on the printer data bus PD7-PD0.
Users can logically OR these two signals as an initial reset.
3. After the above two steps, every time the host system issues an IOR or IOW command, the
W83877AF will compare the I/O address with the CR2 register. If the comparison matches, the
data, low bits addresses (XA2-XA0), and
XWR
/
XRD
will be presented on the parallel port DB-25
connector.
4. DMA operations are handled in the same way as item 3, except that the relevant PDACKX
,
PDRQX will be active on the DB-25 connector.
相關PDF資料 |
PDF描述 |
|---|---|
| W83877ATD | enhanced version from Winbonds most popular I/O chip W83877F |
| W83877ATF | enhanced version from Winbonds most popular I/O chip W83877F |
| W83877 | WINBOND I/O |
| W83877F | WINBOND I/O |
| W83877TD | I/O chip disk drive adapter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83877ATD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:enhanced version from Winbonds most popular I/O chip W83877F |
| W83877ATF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:enhanced version from Winbonds most popular I/O chip W83877F |
| W83877F | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O |
| W83877TD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O |
| W83877TF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O |
發布緊急采購，3分鐘左右您將得到回復。