- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C840AF (WINBOND ELECTRONICS CORP) 100/10Mbps Ethernet Controller PDF資料下載
參數資料
| 型號： | W89C840AF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 100/10Mbps Ethernet Controller |
| 中文描述： | 1 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP128 |
| 封裝： | PLASTIC, QFP-128 |
| 文件頁數： | 25/82頁 |
| 文件大小： | 918K |
| 代理商： | W89C840AF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
W89C840AF
-
25
-
Publication Release Date:October 2000
Revision 1.01
The Fast_Ethernet_Select in C18/CNCR register is used to select the mode in which the W89C840AF
is working in 10M or 100Mbps. In 100Mbps (100BASE) mode, the MAC will not check the SQE status when
transmitting a packet. In 10Mbps(10BASE) mode, the SQE signal will be checked by MAC. No further
function is controlled by the Fast_Ethernet_Select of C18/CNCR register.
Device identifying function
This function is to utilize the device configuration data stored in the device configuration registers, in
which some of them loaded from the external EEPROM. You can tell the vendor, device type, revision,
signature and your own defined code through reading the contents of these registers.
The F00/FID is a read-only register which contains the vendor ID. and device ID., used for
identification. Its
_
contents is loaded from the external EEPROM when hardware reset only.
The second read only register F08/FREV used for identification. It contains the revision ID. which is
also loaded from EEPROM only. The Ethernet device identification code is also included in F08/FREV, but it
is a built in code, not loaded form EEPROM.
Another identification register is the F40/FSR, a read only, too. The signature code for Winbond
W89C840AF is built in the F40/FSR signature register. The 12Hth and 9aHth bytes will be read out
recursively when a number of consecutive PCI configuration space read operation is accessed to the F40/FSR.
The first, third, fifth,...etc. odd read operation will get 12H, however, the second, fourth, sixth,...etc. even read
operation will get 9aH.
For some special requirement, the field of driver area of F40/FSR can be used as a word-width data
buffer for latching the user defined identification code.
EEPROM hardware reset auto load and software programming function
The following configuration parameters should be stored in a EEPROM device for configuring the
W89C840AF and can be loaded into the corresponding configuration register while power-on reset occurring.
1) 6 bytes Ethernet ID.
2) 2 bytes subsystem ID.
3) 2 bytes subsystem vendor ID.
4) 2 bytes device ID.
5) 2 bytes vendor ID.
6) 1 bytes revision ID.
7) 1 byte booting device size
,
power Management capability support and remote wake-up from LAN
8) 1 byte maximum latency
9) 1 byte minimum grant
相關PDF資料 |
PDF描述 |
|---|---|
| W89C841F | 3-IN - 1 10/100M FAST ETHERNET CONTROLLER |
| W89C880F | 100Base-Tx/T4 Multiport Repeater Controller(100Base-Tx/T4多端口中繼器控制器) |
| W89C92 | PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C926 | PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C926F | 10M PCMCIA Ethernet Network Interface Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C840F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN NODE CONTROLLER |
| W89C841D | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3-IN - 1 10/100M FAST ETHERNET CONTROLLER |
| W89C841F | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3-IN - 1 10/100M FAST ETHERNET CONTROLLER |
| W89C841F/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:3-IN-1 100BASE-TX/FX & 10BASE-T Ethernet Controller |
| W89C880F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Hub Controller |
發布緊急采購，3分鐘左右您將得到回復。